Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Practice Tests 2026 | Pass 350-401 with confidence!
Practice CCNP Enterprise 350-401 exam. Online Exam Practice Tests with detailed explanations!
Cost of the Managing Industrial Networks with Cisco 350-401 Exam is as follows:
You have to pay $300 USD for the Managing Industrial Networks with Cisco Networking Technologies (IMINS) Cisco 350-401 Exam. Nice to know that you have to pay the exam fee only once. Purchasing 350-401 Exam has no additional fees. Support is available on Cisco.com by visiting the Learning Network and Caf-Pow.
The Cisco 350-401 exam covers a wide range of topics, including network automation, network security, virtualization, network assurance, and infrastructure services. It is intended for individuals who have a solid understanding of networking fundamentals and have experience working with Cisco networking technologies.
NEW QUESTION # 201
What are three valid HSRP states? (Choose three)
- A. learning
- B. speak
- C. listen
- D. IN IT
- E. full
- F. established
Answer: A,B,C
Explanation:
HSRP consists of 6 states:
Please notice that not all routers in a HSRP group go through all states above. In a HSRP group, only one router reaches active state and one router reaches standby state. Other routers will stop at listen state.
NEW QUESTION # 202
Refer to the exhibit.
Security policy requires all idle-exec sessions to be terminated in 600 seconds. Which configuration achieves this goal?
- A. line vty 0 4
exec-timeout 600 - B. line vty 0 15
exec-timeout - C. line vty 0 15
absolute-timeout 600 - D. line vty 01 5
exec-timeout 10 0
Answer: D
Explanation:
The exec-timeout command is used to configure the timeout for the exec session on a Cisco router or switch.
This command takes two arguments: the first is the timeout in minutes, and the second is the timeout in seconds. To meet the security policy of terminating all idle-exec sessions in 600 seconds (which equals to 10 minutes), option C "line vty 0 4 exec-timeout 10 0" should be used. This configuration sets an exec timeout of ten minutes and zero seconds on vty lines from zero to four, effectively meeting the security policy requirement. References := For further details, you can refer to Cisco's official documentation on the exec-timeout command here.
NEW QUESTION # 203
While configuring an IOS router for HSRP with a virtual IP of 10 1.1.1. an engineer sees this log message.
Which configuration change must the engineer make?
- A. Change the HSRP virtual address on the remote router to 10.1.1.1
- B. Change the HSRP group configuration on the local router to 1.
- C. Change the HSRP virtual address on the local router to 10.1.1.1
- D. Change the HSRP group configuration on the remote router to 1.
Answer: B
NEW QUESTION # 204
Refer to the exhibit.
An engineer must deny Telnet traffic from the loopback interface of router R3 to the loopback interface of router R2 during the weekend hours. All other traffic between the loopback interfaces of routers R3 and R2 must be allowed at all times. Which command accomplish this task?
- A.
- B.
- C.
- D.
Answer: B
Explanation:
We cannot filter traffic that is originated from the local router (R3 in this case) so we can only configure the ACL on R1 or R2. "Weekend hours" means from Saturday morning through Sunday night so we have to configure: "periodic weekend 00:00 to 23:59".
Note: The time is specified in 24-hour time (hh:mm), where the hours range from 0 to 23 and the minutes range from 0 to 59.
NEW QUESTION # 205
Based on the router's API output In JSON format below, which Python code will display the value of the 'role' key?
- A. Option D
- B. Option B
- C. Option C
- D. Option A
Answer: B
Explanation:
The correct Python code to display the value of the 'role' key, based on the router's API output in JSON format, is Option B. In this option, json_data is assigned the JSON content from response.json(). Then it prints the value associated with the 'role' key which is nested inside 'family', which in turn is nested inside
'response'. The syntax json_data['response']['family']['role'] is used to access nested dictionaries in Python. References: For an exact reference, please consult the Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide.
NEW QUESTION # 206
Which statement about agent-based versus agentless configuration management tools is true?
- A. Agentless tools require no messaging systems between master and slaves.
- B. Agent-based tools do not require a high-level language interpreter such as Python or Ruby on slave nodes.
- C. Agent-based tools do not require installation of additional software packages on the slave nodes.
- D. Agentless tools use proxy nodes to interface with slave nodes.
Answer: B
Explanation:
Agentless tool means that no software or agent needs to be installed on the client machines that
are to be managed. Ansible is such an agentless tool. In contrast to agentless tool, agent-based
tool requires software or agent to be installed on the client. Therefore the master and slave nodes
can communicate directly without the need of high-level language interpreter.
An agentless tool uses standard protocols, such as SSH, to push configurations down to a device
(and it can be considered a "messaging system").
NEW QUESTION # 207
What is the function of an EIGRP sequence TLV packet?
- A. to list the peers that should listen to the next multicast packet during the reliable multicast process
- B. to define the initial sequence number when bringing up a new peer
- C. to acknowledge a set of sequence numbers during the startup update process
- D. to list the peers that should not listen to the next multicast packet during the reliable multicast process
Answer: D
NEW QUESTION # 208
Refer to the exhibit.
What are two effect of this configuration? (Choose two.)
- A. The 10.1.1.0/27 subnet is assigned as the inside local addresses.
- B. Inside source addresses are translated to the 209.165.201.0/27 subnet.
- C. The 10.1.1.0/27 subnet is assigned as the inside global address range.
- D. The 209.165.201.0/27 subnet is assigned as the outside local address range.
- E. It establishes a one-to-one NAT translation.
Answer: A,B
NEW QUESTION # 209
Refer to the exhibit.
The inside and outside interfaces u configuration of this device have been correctly identified. What is the effect of this configuration?
- A. NAT64
- B. dynamic NAT
- C. static NAT
- D. PAT
Answer: D
Explanation:
The configuration in the exhibit indicates the use of Port Address Translation (PAT). The "overload" keyword at the end of the NAT command signifies that multiple internal IP addresses will be translated to a single public IP address, with each session differentiated by a unique port number. This is a characteristic feature of PAT, which allows numerous devices on a local network to share a single public IP address while maintaining unique sessions. References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide.
NEW QUESTION # 210
Refer to the exhibit.
Both controllers are in the same mobility group. Which result occurs when client 1 roams between APs that are registered to different controllers in the same WLAN?
- A. The client database entry moves from controller A to controller B.
- B. Client 1 users an EoIP tunnel to contact controller A.
- C. CAPWAP tunnel is created between controller A and controller B.
- D. Client 1 contact controller B by using an EoIP tunnel.
Answer: A
Explanation:
When a client roams between APs that are registered to different controllers within the same WLAN, the client's database entry moves from the original controller (Controller A) to the new controller (Controller B).
This process ensures that the client maintains its connection and experiences seamless mobility. The controllers share information about the client, such as authentication credentials, so that there is no need for re-authentication when moving between APs connected to different controllers. References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide.
NEW QUESTION # 211
Refer to the exhibit.
What is output by this code?
- A. 8 7 6 5
- B. -4 -5 -6 -7
- C. -1 -2-3-4
- D. 4 5 6 7
Answer: A
Explanation:
The code snippet provided in the exhibit is a simple Python program that initializes a variable count with the value of 8. It then enters a while loop that continues executing as long as count is greater than 4. Inside the loop, it prints the current value of count and then decrements count by one each iteration. As a result, it will print the numbers 8, 7, 6, and 5 before count becomes less than or equal to four and the loop terminates.
NEW QUESTION # 212
Refer to the exhibit.
An engineer must allow all users In the 10.2.2.0/24 subnet to access the Internet. To conserve address space, the public interface address of 209.165.201.1 must be used for all external communication. Which command set accomplishes these requirements?
A)
B)
C)
D)
- A. Option B
- B. Option D
- C. Option C
- D. Option A
Answer: B
Explanation:
Explanation
The command ip nat inside source list 10 interface G0/3 overload configures NAT to overload (PAT) on the address that is assigned to the G0/3 interface.
NEW QUESTION # 213
Which devices does Cisco Center configure when deploying an IP-based access control policy?
- A. all devices in selected sites
- B. All devices integrating with ISE
- C. selected individual devices
- D. all wired devices
Answer: B
Explanation:
Explanation
When you click Deploy, Cisco DNA Center requests the Cisco Identity Services Engine (Cisco ISE) to send notifications about the policy changes to the network devices.
NEW QUESTION # 214
Refer to the exhibit.
An engineer must block all traffic from a router to its directly connected subnet 209.165.200.0/24. The engineer applies access control list EGRESS in the outbound direction on the GigabitEthernet0/0 interface of the router However, the router can still ping hosts on the 209.165.200.0/24 subnet. Which explanation of this behavior is true?
- A. Access control lists that are applied outbound to a router interface do not affect traffic that is sourced from the router.
- B. Only standard access control lists can block traffic from a source IP address.
- C. After an access control list is applied to an interface, that interface must be shut and no shut for the access control list to take effect.
- D. The access control list must contain an explicit deny to block traffic from the router.
Answer: A
NEW QUESTION # 215
Drag and drop the REST API authentication methods from the left onto their descriptions on the right.
Answer:
Explanation:
Explanation
A close-up of a graph Description automatically generated with low confidence
NEW QUESTION # 216
Drag and drop the characteristics from the left onto the appropriate infrastructure deployment types on the right.
Answer:
Explanation:
NEW QUESTION # 217
Refer to the exhibit.
Which antenna emits this radiation pattern?
- A. omnidirectional
- B. RP-TNC
- C. dish
- D. Yagi
Answer: A
NEW QUESTION # 218
Drag and drop characteristics of PIM dense mode from the left to the right.
Answer:
Explanation:
PIM-DM supports only source trees - that is, (S,G) entries-and cannot be used to build a shared distribution tree.
Reference:
PIM dense mode (PIM-DM) uses a push model to flood multicast traffic to every corner of the network. This push model is a brute-force method of delivering data to the receivers. This method would be efficient in certain deployments in which there are active receivers on every subnet in the network. PIM-DM initially floods multicast traffic throughout the network. Routers that have no downstream neighbors prune the unwanted traffic. This process repeats every 3 minutes.
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
In PIM dense mode (PIM-DM), multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
NEW QUESTION # 219
Which statement explains why Type 1 hypervisor is considered more efficient than Type 2 hypervisor?
- A. Type 1 hypervisor is the only type of hypervisor that supports hardware acceleration techniques.
- B. Type 1 hypervisor enables other operating systems to run on it.
- C. Type 1 hypervisor relics on the existing OS of the host machine to access CPU, memory, storage, and network resources.
- D. Type 1 hypervisor runs directly on the physical hardware of the host machine without relying on the underlying OS.
Answer: D
Explanation:
Explanation
There are two types of hypervisors: type 1 and type 2 hypervisor.
In type 1 hypervisor (or native hypervisor), the hypervisor is installed directly on the physical server. Then instances of an operating system (OS) are installed on the hypervisor. Type 1 hypervisor has direct access to the hardware resources. Therefore they are more efficient than hosted architectures. Some examples of type 1 hypervisor are VMware vSphere/ESXi, Oracle VM Server, KVM and Microsoft Hyper-V.
In contrast to type 1 hypervisor, a type 2 hypervisor (or hosted hypervisor) runs on top of an operating system and not the physical hardware directly. answer 'Type 1 hypervisor runs directly on the physical hardware of the host machine without relying on the underlying OS' big advantage of Type 2 hypervisors is that management console software is not required. Examples of type 2 hypervisor are VMware Workstation (which can run on Windows, Mac and Linux) or Microsoft Virtual PC (only runs on Windows).
NEW QUESTION # 220
......
The best 350-401 exam study material and preparation tool is here: https://examkiller.itexamreview.com/350-401-valid-exam-braindumps.html
